- 您现在的位置：买卖IC网 > Sheet目录321 > DM300019 (Microchip Technology)BOARD DEMO DSPICDEM 80L STARTER
dsPICDEM? 80-Pin Starter Development Board User’s Guide
3.5
BOARD SELF-TEST
The board self-test is provided for completeness only. Users do not need to run this
test.
1. Power the board using a 9V DC supply and the barrel power connector.
The LED marked D1 turns ON.
If D1 does not light:
- the LED is dead, or
- the regulator is dead, or
- the DC supply is not connected to the AC wall plug
2. Using a DMM set for DCV, check that 3.3V or 5.0V is available at location marked
V DD and GND on the 80-pin header.
3. Connect a shorting plug on the RS-232 connector J1. This shorting plug should
have pins 2 and 3 connected to one another.
4. Short pins 2 and 3 on line connector J9 using a 0.1 ″ jumper.
5. Make sure J4 has a 0.1 ″ jumper on it.
6. To enter the Self-Test mode, hold down S1, press and release MCLR, then
release S1.
The following four tests should run:
Test
UART Test
Keypad Test
Description
This automatic test transmits 5 characters and receives them through
the serial port. During the test, LED RD4 blinks at a very fast rate
(8 blinks/sec). However, this test completes so quickly that, in most
instances, no noticeable blink of RD4 will occur.
During this test, LED RD5 blinks very fast. You must respond by pressing
S1 and S2. When you press S1, RD4 lights. When you press S2, RD7
lights. If both key presses are acknowledged by the dsPIC ? DSC, then
the test passed. If you get no response or an incorrect response within 4
seconds, then the test is considered failed. In either case the test
automatically proceeds to the Potentiometer test.
Potentiometer Test During this test, LED RD6 blinks rapidly. You must first respond by turn-
ing Potentiometer R13 fully clockwise (RD4 will light) and then fully coun-
terclockwise (RD7 will light). Then you must move the potentiometer
wiper to a center position causing RD5 to light up. When this happens,
the test is complete. This test must be completed in 8 seconds or else the
test is considered failed.
DS51584B-page 30
Tone Test
This procedure automatically tests the digital potentiometer and analog
operational amplifier. A sine wave, generated using the digital potentiom-
eter, is sent through the Op Amp circuit to the ADC of the dsPIC DSC
device. The sine wave is analyzed to determine if a smooth sine wave
has been generated. If all works well, the test passes. If there is a fault in
the op amp or digital potentiometer, then this test fails.
? 2006 Microchip Technology Inc.
发布紧急采购，3分钟左右您将得到回复。
相关PDF资料
DM300024
KIT DEMO DSPICDEM 1.1
DM330012
KIT USB STARTER FOR DSPIC33E
DM330013
MICROSTICK DSPIC33F/PIC24H BOARD
DNET1
SURGE SUPPRESSOR ETHERNET RJ45
DR-8094
RACK DOUBLE 84"X20.25"X36" BLK
DR-IAC5E
INPUT MODULE AC 5VDC
DRIDC24A
INPUT MODULE DC 34MA 24VDC
DRODC24
OUTPUT MODULE DC 13MA 24VDC
相关代理商/技术参数
DM300019
制造商:Microchip Technology Inc 功能描述:DEMO BOARD STARTER ((NW))
DM300020
功能描述:开发板和工具包 - PIC / DSPIC dsPICDEM MC1 Motor C RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM300021
功能描述:开发板和工具包 - PIC / DSPIC High V Pwr Module RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM300021
制造商:Microchip Technology Inc 功能描述:MODULE dsPICDEM MC1H 3 PHASE
DM300022
功能描述:开发板和工具包 - PIC / DSPIC Low V Pwr Module RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM300023
功能描述:开发板和工具包 - PIC / DSPIC dsPICDEM SMPS Buck Demo Brd RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM300024
功能描述:开发板和工具包 - PIC / DSPIC dsPICDEM 1.1 GP RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压:
DM300027
功能描述:开发板和工具包 - PIC / DSPIC 16-bit Starter Demo Board RoHS:否 制造商:Microchip Technology 产品:Starter Kits 工具用于评估:chipKIT 核心:Uno32 接口类型: 工作电源电压: